Looking for a meter of fuel-grade hose for my oil catch can installation. I can get it on lazada but pretty sure it can be had down Udon's own motor alley. Anyone know of a dead cert shop rather than me going door to door?
.
Ta
tam
3/4" / 19 mm hose
3/4" / 19 mm hose
'Don't waste your words on people who deserve your silence'
~Reinhold Messner~
'You don't have to be afraid of everything you don't understand'
~Louise Perica~
~Reinhold Messner~
'You don't have to be afraid of everything you don't understand'
~Louise Perica~
Re: 3/4" / 19 mm hose
Can't say for sure, but as you're heading toward Makro from the fountain circle, on your left hand side probably not more than 75m from the circle, there are 2 shops that sell a variety of things like this. I believe the owner of the first shop speaks English (might be the second shop). In any case, show him what you're looking for.....I'll bet he has it.
- sometimewoodworker
- udonmap.com
- Posts: 3404
- Joined: October 7, 2008, 11:19 am
Re: 3/4" / 19 mm hose
If that doesn’t work then try ToolPro it’s likely that they will have it.
Jerome and Nui's new househttp://bit.ly/NJnewHouse
In my posts all fees and requirements are the standard R&R but TIT and a brown envelope can make incredible changes YMMV.
In my posts all fees and requirements are the standard R&R but TIT and a brown envelope can make incredible changes YMMV.
Re: 3/4" / 19 mm hose
Toolpro would be my first option
I had a bumper sticker in Texas that read 'Beam me up Scotty'. I often wish I could find one in Udon Thani
Re: 3/4" / 19 mm hose
I agree with youparrot wrote: ↑February 4, 2022, 12:26 pmCan't say for sure, but as you're heading toward Makro from the fountain circle, on your left hand side probably not more than 75m from the circle, there are 2 shops that sell a variety of things like this. I believe the owner of the first shop speaks English (might be the second shop). In any case, show him what you're looking for.....I'll bet he has it.
Those shops seem to have every accessory in them
- stattointhailand
- udonmap.com
- Posts: 19114
- Joined: October 25, 2007, 11:34 pm
- Location: Oiling the locks on my gun case
Re: 3/4" / 19 mm hose
Sorry couldn't resist
-
- udonmap.com
- Posts: 1240
- Joined: April 21, 2020, 8:37 pm
Re: 3/4" / 19 mm hose
did you buy some kind of kit that's missing a bit
of hose? even that looks to be a serious headache
i briefly watched a mishimoto install barf
heater core hose is commonly 5/8 and 3/4 i think
sae j20 that high pressure oil/ fuel line j30r6 gets increasingly unflexible. doesnt look like fun at all
of hose? even that looks to be a serious headache
i briefly watched a mishimoto install barf
heater core hose is commonly 5/8 and 3/4 i think
sae j20 that high pressure oil/ fuel line j30r6 gets increasingly unflexible. doesnt look like fun at all
-
- udonmap.com
- Posts: 1240
- Joined: April 21, 2020, 8:37 pm
Re: 3/4" / 19 mm hose
this isn't a new problem ( unexplained oil loss) or
simple piston ring wear blamed as culprit. i think
there's slightly more to it than that
the supposed remedy even ( catch cans around for decades) installed inline with the pcv system
i started reading about it as it pertained to 350z
with people saying they had to add a quart every
1,000-1,500 miles. well, thats just not right
simple piston ring wear blamed as culprit. i think
there's slightly more to it than that
the supposed remedy even ( catch cans around for decades) installed inline with the pcv system
i started reading about it as it pertained to 350z
with people saying they had to add a quart every
1,000-1,500 miles. well, thats just not right